LiftMaster PROFESSIONAL
Model 374LM 315MHz Security + 4 Channel Remote Control
The 374
315MHz remote control can activate four separate 315MHz Security+
residential or commercial garage door openers and or gate openers. The
instructions for programming garage door openers are listed below. Please
refer to the original receiver programming for commercial and gate operators.
All four
push buttons work with 315 MHz Security+ receivers having a purple
"learn" button. The rolling code between these channels and the receiver changes with
each use, randomly accessing over 100 billion new codes.
As an added
feature, the 4th button is capable of learning or being trained to duplicate or
match another CGI manufactured 315MHz fixed code remote. This feature is
normally used when several remotes are required to operate on fixed code devise
such as a gate operator or commercial dock door. In this case, the code
transmitter to the receiver remains constant or fixed, not using the Security+
format.
************* WARNING *************
Moving Door can cause serious injury or death.
·
DO NOT install transmitter
unless the door operator’s safety reverse works as required by the door
operator’s manual.
·
Wall control must be
mounted in sight of door, at least 5 feet above floor and clear of moving door
parts.
·
Keep people
clear of opening while door is
moving.
·
DO NOT
allow children to play with the
transmitter or door operator.
If safety
reverse does not work properly:
·
Close door then disconnect operator
using the manual release handle.
·
DO NOT
use transmitter or door operator.
·
Refer to Door and Door
Operators Owner’s Manuals before attempting any repairs.
_________________________________________________
Electrical Shock
can cause serious injury or death.
·
Power cord must be unplugged
before attaching any wires,
·
Be sure wire ends do not touch
each other or other terminals.
If you have questions or if you need a manual, contact the
distributor or manufacturer of the operator.
Programming
instructions are described below.
WHEN USED WITH SECURITY+ GARAGE DOOR OPENERS
To
program the opener to accept the remote control code:
- Press and release the
“Learn" button on the opener panel. This
can be found where you see the antenna wire hanging from the motor head (you
may have to take the lens cover off). If antenna wire is not hanging from
motor head then you have an external receiver which is a black box approx. 6"
x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop
off cover to find Learn Code Button). The
indicator light on the panel will begin to blink and the opener lights will
flash once.
- Within 30 seconds,
press and hold the button on the hand held remote that you wish to operate
your garage door.
- Release the button when
the motor unit lights blink. It has learned the code. If light
bulbs are not installed, two clicks will be heard.
Now the opener will operate when that push button is pressed.
To
erase all remote control codes from the receiver:
Press and
hold the “Learn” button on opener panel until the indicator light turns off
(about 6 seconds). All transmitter codes inside the receiver are now erased.
Then follow the steps above to re-program each remote control.
When
Several Remotes operate one device:
To match
the 374LM to another CGI manufactured remote’s code (Remote Control X):
- Begin by having both the
374LM and Remote Control X available.
- With the 374LM button
side up, press and hold both 1st and 4th push buttons
until the yellow indicator light begins to blink. Visible at the bottom
through a small hole begins to blink. It will blink for 30
seconds; during this time it is in “learn” mode. and the buttons can be
released.
- While it is in learn
mode, hold remote control X, another CGI fixed code transmitter back to back
with the FCC labels touching.
- Press and hold the
Remote Control X push button as you slowly slide the remotes across each other
until the 374LM indicator light blinks very rapidly, indicating it has learned
the code. (If Remote Control X is a 374 , you must press and hold its
4th push button).
- The 4th button is now
sending the same identical coded signal as Remote Control X. This code
will remain inside the 374LM until replaced with another new code by repeating
steps 1-4 above, or by resetting to Security+
Now the device will operate when the 4th push
button is pressed.
This code will remain inside the remote control until replaced
with a new code by repeating the above steps.
Resetting the 4th push button
back to Security+ as follows:
Push and hold the 1st and 4th
buttons while observing the small yellow indicator light. Hold both button
for 10 seconds until the yellow indicator light stops blinking. The remote
has defaulted to one of six randomly preprogrammed Security+ settings.
The
Remote Control Batteries:
The Lithium
batteries should produce power for up to 5 years. To replace, pry open case with
visor clip or screwdriver. Insert batteries positive side up (+). Dispose of old
batteries properly.
|